<?xml version="1.0" encoding="UTF-8"?>

 DiameterPeer Parameters 
  - FQDN - FQDN of this peer, as it should apper in the Origin-Host AVP
  - Realm - Realm of this peer, as it should apper in the Origin-Realm AVP
  - Vendor_Id - Default Vendor-Id to appear in the Capabilities Exchange
  - Product_Name - Product Name to appear in the Capabilities Exchange 
  - AcceptUnknownPeers - Whether to accept (1) or deny (0) connections from peers with FQDN 
    not configured below
  - DropUnknownOnDisconnect - Whether to drop (1) or keep (0) and retry connections (until restart)
    unknown peers in the list of peers after a disconnection.
  - Tc - Value for the RFC3588 Tc timer - default 30 seconds
  - Workers - Number of incoming messages processing workers forked processes.
    This only matters in ser_ims.
    In Wharf, the Wharf workers pool are reused for this purpose.
   - Queue - Length of queue of tasks for the workers:
     - too small and the incoming messages will be blocked too often;
     - too large and the senders of incoming messages will have a longer feedback loop to notice that
     this Diameter peer is overloaded in processing incoming requests;
     - a good choice is to have it about 2 times the number of workers. This will mean that each worker
     will have about 2 tasks in the queue to process before new incoming messages will start to block.
  - ConnectTimeout - time in seconds to wait for an outbound TCP connection to be established.
  - TransactionTimeout - time in seconds after which the transaction timeout callback will be fired,
    when using transactional processing.
  - SessionsHashSize - size of the hash-table to use for the Diameter sessions. When searching for a 
    session, the time required for this operation will be that of sequential searching in a list of 
    NumberOfActiveSessions/SessionsHashSize. So higher the better, yet each hashslot will consume an
    extra 2xsizeof(void*) bytes (typically 8 or 16 bytes extra).
  - DefaultAuthSessionTimeout - default value to use when there is no Authorization Session Timeout 
  AVP present.
  - MaxAuthSessionTimeout - maximum Authorization Session Timeout as a cut-out measure meant to
  enforce session refreshes.
		Definition of peers to connect to and accept connections from. For each peer found in here
		a dedicated receiver process will be forked. All other unkwnown peers will share a single
	<Peer FQDN="hss.open-ims.test" Realm="open-ims.test" port="3868" src_addr=""/>

		Definition of incoming connection acceptors. If no bind is specified, the acceptor will bind
		on all available interfaces.
	<Acceptor port="3868"  />
	<Acceptor port="3869" bind="" />
	<Acceptor port="3870" bind="" />
		Definition of Auth (authorization) and Acct (accounting) supported applications. This
		information is sent as part of the Capabilities Exchange procedures on connecting to
		peers. If no common application is found, the peers will disconnect. Messages will only
		be sent to a peer if that peer actually has declared support for the application id of 
		the message.
	<Acct id="16777216" vendor="10415" />
	<Acct id="16777216" vendor="0" />
	<Auth id="16777216" vendor="10415"/>
	<Auth id="16777216" vendor="0" />
		Supported Vendor IDs - list of values which will be sent in the CER/CEA in the
		Supported-Vendor-ID AVPs
	<SupportedVendor vendor="10415" />
		Realm routing definition.
		Each Realm can have a different table of peers to route towards. In case the Destination
		Realm AVP contains a Realm not defined here, the DefaultRoute entries will be used.

		Note: In case a message already contains a Destination-Host AVP, Realm Routeing will not be
		Note: Routing will only happen towards connected and application id supporting peers.
		The metric is used to order the list of prefered peers, while looking for a connected and
		application id supporting peer. In the end, of course, just one peer will be selected.
	<Realm name="my.open-ims.test">
		<Route FQDN="blackjack" metric="2"/>
		<Route FQDN="test1" metric="3"/>
		<Route FQDN="test2" metric="5"/>
	<Realm name="test1.open-ims.test">
		<Route FQDN="test3" metric="7"/>
		<Route FQDN="test4" metric="11"/>
	<Realm name="test2.open-ims.test">
		<Route FQDN="test5" metric="13"/>
	<DefaultRoute FQDN="test6" metric="15"/>
	<DefaultRoute FQDN="test7" metric="13"/>